When a CT scanner stops unexpectedly, the X-ray tube is the first component to check. For biomedical engineers, service engineers, and radiology managers, early diagnosis of CT tube failure saves scanner downtime and patient scheduling. This technical guide from Zhuhai RMing Medical (RIMION) explains the 7 most common signs of CT tube failure based on real field data from GE, Siemens, Philips, and Canon systems.
1. Unusual Noise and Vibration During Rotation
The first sign of bearing wear. A healthy CT tube rotates silently at high speed. When you hear grinding, whistling, or increased vibration during scan preparation, the high-speed bearings inside the tube are deteriorating.
What to check: Run a low-mA air scan. If noise increases with gantry speed and disappears when tube is not rotating, bearing failure is likely.
2. Frequent Arcing or High Voltage Errors
Error codes like high voltage failure, tube arcing, or unstable mA often indicate vacuum instability or anode surface damage. The tube may fire normally for a few scans then fail.
What to check: Review error log for intermittent arc counts. If arcing frequency increases after warm-up, tube vacuum enclosure is degrading.
3. Image Artifacts – Rings, Streaks, or Non-Uniformity
Cracked anode target, pitted focal spot, or unstable focal spot causes ring artifacts, streaks, or central bright/dark areas. Calibration may temporarily improve but artifacts return quickly.
What to check: Perform water phantom calibration. If HU uniformity fails repeatedly after calibration, focal track is damaged.
4. Longer Tube Cooling Time and Overheating
If the scanner shows tube cooling delay more often, or heat capacity drops quickly, anode heat dissipation is reduced. This is common after high workload or poor cooling system performance.
5. Filament Current Unstable or No Exposure
Filament burnout or cathode degradation leads to no X-ray output, low mA, or exposure errors. Scanner may show filament error or tube current cannot reach target value.
6. Oil Leak or Visible Damage Around Housing
External oil leakage, discoloration, or cracks in tube housing indicate internal seal failure. This requires immediate shutdown to avoid damage to gantry and high-voltage generator.
7. Scan Seconds Exceed Expected Service Life
Every tube has a rated scan second count. When your system exceeds typical service range and shows 2 or more signs above, planned replacement is more cost-effective than emergency repair.
How to Confirm Tube Failure Before Ordering Replacement
Step 1: Collect Information
- Scanner brand and model: Example GE BrightSpeed, Siemens SOMATOM, Philips Brilliance
- Current tube part number and serial number
- Error log photos and artifact images
- Scan seconds and installation date
Step 2: Run Standard Tests
- Air scan at low mA
- Water phantom calibration and HU uniformity test
- Check bearing noise without X-ray
- Review error and arc counters in service mode
Step 3: Send Data to Factory for Confirmation
RIMION technical team can confirm compatibility and failure analysis from photos and logs. We support GE, Siemens, Philips, and Canon platforms with NMPA-registered compatible models.
What to Prepare for Hospital Tender and Compliance
For formal replacement, hospitals require full documentation. RIMION provides: ISO 13485:2016, ISO 9001, CE, Medical Device Production License, Radiation Safety License, Class II Medical Device Operating Registration, NMPA Registration Certificate, Export Sales Certificate, and factory test report. All documents are available for tender submission.
Key Takeaways
- Bearing noise and vibration is the earliest and most common sign of CT tube wear
- Arcing, image artifacts, and cooling delays indicate anode or vacuum degradation
- Confirm failure with air scan, phantom calibration, and error log review
- Prepare scanner model, tube part number, and error photos to confirm compatible model from an independent manufacturer
FAQ – CT Tube Diagnosis
Can I continue using a CT tube with bearing noise?
Continued use with bearing noise risks sudden tube seizure and damage to gantry. It is recommended to plan replacement and reduce workload immediately, then confirm diagnosis with factory support.
Why does my CT tube keep arcing after calibration?
Recurring arcing after successful calibration indicates vacuum or anode target damage. Calibration cannot repair physical damage inside the tube. Replacement should be evaluated.
How do I know which compatible tube fits my scanner?
Compatibility is confirmed by scanner brand, model, and existing tube part number. Send this information plus scanner photos to RIMION export team for verification within 24 hours.
Does RIMION provide installation guidance?
Yes. RIMION provides remote installation guidance, calibration support, and technical documentation. Our team supports service engineers via WhatsApp +86 131 2857 5663 and email rm01@rmingxray.com.
Need quick diagnosis and compatibility check? Send your scanner brand, model, tube part number, error codes, and artifact photos to rm01@rmingxray.com or WhatsApp +86 131 2857 5663. Factory team replies within 24 hours.

Disclaimer: GE, Siemens, Philips, Canon are trademarks of their respective owners. RIMION is not affiliated with, endorsed by, or sponsored by these companies. Compatibility refers to technical fit only.



